TALK=T;RUN( 1, 1)
************************************************************
Q1 created by VDI menu, Version 2018, Date 17/01/18
CPVNAM=VDI; SPPNAM=FLAIR
************************************************************
Echo DISPLAY / USE settings
DISPLAY
Library Case I403: Deposition, horizontal duct @ 5.3m/s
The case considered is 3d steady, isothermal, turbulent air flow
in a horizontal square ventilation duct with the transport
and deposition of particles. The Eulerian drift flux model is
used to simulate particles with deposition by means of the
3-layer deposition model of Chen & Lai (2004), which accounts
for deposition by gravity, Brownian diffusion and turbophoresis.
This case has been studied experimentally by Sippola and Nazaroff
(2004), who for fully-developed flow, measured deposition rates
of particles to the walls of the duct with nominal sizes ranging
from 1 to 16 microns in a 0.152m square duct at each of three
nominal air speeds: 2.2m/s, 5.3m/s, 9m/s, corresponding to
Reynolds numbers of 21,957, 53,894 & 87,733. This particular Q1
file employs the highest air speed of 5.3m/s at a temperature of
23degC so as to replicate Runs 7 to 11 of the experimental series,
which consider deposition of 5 different particle sizes onto the
four walls of the duct in the fully-developed region of the flow.
ENDDIS
PHOTON USE
p
up x
view y
con C6 y 1 fi;.1;pa
vec y 1;pa
ENDUSE
************************************************************
IRUNN = 1 ;LIBREF = 0
************************************************************
Group 1. Run Title
TEXT(I403: Deposition, horizontal [email protected]/s)
************************************************************
Echo save-block settings for Group 1
save1begin
Five different mono-sized aerosol particles with differing
densities enter the horizontal duct with supply air at 5.3m/s
and 23degC. The duct is 20 hydraulic diameters long, at
which location the flow is essentially fully developed. In
the simulations the particle concentration is normalized by
the inlet concentration. The flow is symmetric about the duct
centre, but this isn't exploited in the simulations. The case
has been studied numerically by Zhao and Wu (2006).
This particular Q1 file simulates the intermediate air speed case
so as to replicate Runs 7 to 11 of the experimental series,
which have the following aerosol characteristics:
Run diameter density Tr+ Vd+ Tr+ Vd+
(microns) (kg/m^3) measured predicted
7 1.0 1400 0.022 2.0E-4 0.024 1.849E-4
8 3.1 1200 0.16 1.5E-3 0.175 1.638E-3
9 5.2 1200 0.48 7.9E-3 0.481 6.377E-3
10 9.8 1000 1.5 0.017 1.403 0.0453
11 16.0 1000 3.6 0.069 3.716 0.1895
where Tr+ (=Tr*Ust^2/enul_g) is the dimensional particle relaxation
time, Vd+ (=Vd/Ust)is the dimensionless deposition velocity, enul_g
is the kinematic laminar viscosity, Ust (=0.27m/s) is the friction
velocity, Tr (=rho_p*diam_p^2*C/(18.*rho_g*enul_g) is the particle
relaxation time and C is the Cunningham slip coefficient.
References
----------
Sippola, M.R. & Nazaroff,W.W., "Experiments Measuring Particle
Deposition from Fully Developed Turbulent Flow in Ventilation
Ducts", Aerosol Science & Technology, Vol.38, pp914–925,
(2004)
Sippola, M.R., "Particle Deposition in Ventilation Ducts", PhD
Thesis, Civil and Environmental Engineering, University of
California, Berkeley, (2002).
Zhao, B. & Wu, J., "Modelling particle deposition from fully
developed flow in ventilation duct", J. Atmospheric
Environment, Vol.40, p457-466, (2006).
Chen, F.Z. & Lai, A.C.K, "An Eulerian model for particle
deposition under electrostatic and turbulent conditions",
J.Aerosol Science, Vol.35, p47-62, (2004).
save1end
************************************************************
Group 2. Transience
STEADY = T
************************************************************
Groups 3, 4, 5 Grid Information
* Overall number of cells, RSET(M,NX,NY,NZ,tolerance)
RSET(M,60,30,30)
************************************************************
Group 6. Body-Fitted coordinates
************************************************************
Group 7. Variables: STOREd,SOLVEd,NAMEd
* Non-default variable names
NAME(106)=ENUN ;NAME(107)=DI5
NAME(108)=DI4 ;NAME(109)=DI3
NAME(110)=DI2 ;NAME(111)=VP5
NAME(112)=TP5 ;NAME(113)=VP4
NAME(114)=TP4 ;NAME(115)=VP3
NAME(116)=TP3 ;NAME(117)=VP2
NAME(118)=TP2 ;NAME(119)=VS5
NAME(120)=TR5 ;NAME(121)=VD5
NAME(122)=DEP5 ;NAME(123)=VS4
NAME(124)=TR4 ;NAME(125)=VD4
NAME(126)=DEP4 ;NAME(127)=VS3
NAME(128)=TR3 ;NAME(129)=VP1
NAME(130)=TP1 ;NAME(131)=DI1
NAME(132)=VS1 ;NAME(133)=TR1
NAME(134)=VD1 ;NAME(135)=VD3
NAME(136)=VSTR ;NAME(137)=DEP1
NAME(138)=DEP3 ;NAME(139)=VS2
NAME(140)=ENUL ;NAME(141)=TR2
NAME(142)=VD2 ;NAME(143)=DEP2
NAME(145)=YPLS ;NAME(146)=STRS
NAME(147)=EPKE ;NAME(148)=DEN1
NAME(149)=EL1 ;NAME(150)=ENUT
* Solved variables list
SOLVE(P1,U1,V1,W1,C6,C7,C8,C9)
SOLVE(C10)
* Stored variables list
STORE(ENUT,EL1,DEN1,EPKE,STRS,YPLS,DEP2,VD2)
STORE(TR2,ENUL,VS2,DEP3,DEP1,VSTR,VD3,VD1)
STORE(TR1,VS1,DI1,TP1,VP1,TR3,VS3,DEP4)
STORE(VD4,TR4,VS4,DEP5,VD5,TR5,VS5,TP2)
STORE(VP2,TP3,VP3,TP4,VP4,TP5,VP5,DI2)
STORE(DI3,DI4,DI5,ENUN)
* Additional solver options
SOLUTN(P1,Y,Y,Y,N,N,Y)
SOLUTN(C6,Y,Y,Y,N,N,Y)
SOLUTN(C7,Y,Y,Y,N,N,Y)
SOLUTN(C8,Y,Y,Y,N,N,Y)
SOLUTN(C9,Y,Y,Y,N,N,Y)
SOLUTN(C10,Y,Y,Y,N,N,Y)
TURMOD(KEMODL)
************************************************************
Echo save-block settings for Group 7
save7begin
(stored of ENUN is ENUT/(0.152*0.43))
save7end
************************************************************
Group 8. Terms & Devices
NEWRH1 = T
NEWENL = T
************************************************************
Group 9. Properties
PRESS0 =1.01325E+05 ;TEMP0 =273.
* Domain material index is 2 signifying:
* Air using Ideal Gas Law, STP
SETPRPS(1, 2)
ENUL = GRND6
ENULA =1.46E-06 ;ENULB =110.
ENULC =8.0974E-11
TMP1 = GRND1
TMP1A =23. ;TMP1B =0.
TMP1C =0.
DRH1DP = GRND5
DVO1DT =3.33E-03
PRT(EP)=1.314
************************************************************
Group 10.Inter-Phase Transfer Processes
************************************************************
Group 11.Initialise Var/Porosity Fields
FIINIT(P1)=0. ;FIINIT(U1)=5.3
FIINIT(C6)=0. ;FIINIT(C7)=0.
FIINIT(C8)=0. ;FIINIT(C9)=0.
FIINIT(C10)=0.
No PATCHes used for this Group
INIADD = F
************************************************************
Group 12. Convection and diffusion adjustments
No PATCHes used for this Group
************************************************************
Group 13. Boundary & Special Sources
PATCH(DFLUX, CELL, 0, 0, 0, 0, 0, 0, 1, 1)
COVAL(DFLUX, C6, GRND4, GRND4)
COVAL(DFLUX, C7, GRND4, GRND4)
COVAL(DFLUX, C8, GRND4, GRND4)
COVAL(DFLUX, C9, GRND4, GRND4)
COVAL(DFLUX, C10, GRND4, GRND4)
BUOYA =0. ; BUOYB =0.
BUOYC =-9.81
EGWF = T
************************************************************
Echo save-block settings for Group 13
save13begin
** estimate for turbulent inlet intensity
for fully developed duct flow
real(din,win,tint,kein,epin,mixl,fric,temk)
real(reyn,ust,tvis,tvisn,enugas,rhogas)
temk=23.0+temp0
din=0.152
win=5.3
rhogas=press0/(287.0*temk)
rhogas
enugas=1.46e-6*temk**1.5/(110.+temk)/rhogas
enugas
reyn=win*din/enugas
reyn
fric=1./(1.82*log10(reyn)-1.64)**2
fric
ust=win*(fric/8.)**0.5
ust
kein=fric*win*win/4.
mixl=0.09*0.5*din
mixl
epin=0.1643*kein**1.5/mixl
kein
epin
tint=kein**0.5/win
tint
tvis=0.09*kein*kein/epin
tvis
tvisn=tvis/(ust*din)
tvisn
real(vslip,rho_p,dpart,grava,vdep,rey,tpart,tpl)
integer(npart);npart=5
** Particle diameter & density
array(pdia,real,npart)
array(pden,real,npart)
pdia(1)=1.0;pdia(2)=3.1;pdia(3)=5.2
pdia(4)=9.8;pdia(5)=16.0
pden(1)=1400.0;pden(2)=1200.0;pden(3)=1200.0
pden(4)=1000.0;pden(5)=1000.0
do ii=1,npart
dpart=pdia(ii)*1.e-6
rho_p=pden(ii)
** Stokes-flow slip velocity
grava=9.81
vslip=rho_p*dpart*dpart*grava/(18.*rhogas*enugas)
rey=vslip*dpart/enugas
ii
vdep=vslip
vslip
rey
tpart=rho_p*dpart**2/(18.*rhogas*enugas)
tpart
tpl=tpart*ust*ust/enugas
tpl
enddo
** print to the "inforout" file the floor deposition
results in the fully-developed flow region.
integer(ixp,iyp)
ixp=nx
iyp=ny/2
(make1 vs_nx is 0)
(store1 vs_nx is VSTR[:ixp:,:iyp:,1])
(print V* is vs_nx)
(make1 yp_nx is 0)
(store1 yp_nx is YPLS[:ixp:,:iyp:,1])
(print y+ is yp_nx)
do jj=1,npart
(make1 tr_:jj: is 0)
(store1 tr_:jj: is TR:jj:[:ixp:,:iyp:,1])
(print Tr_:jj: is tr_:jj:)
(make1 vd_:jj: is 0)
(store1 vd_:jj: is VD:jj:[:ixp:,:iyp:,1])
(print Vd_:jj: is vd_:jj:)
(make1 tp_:jj: is 0)
(store1 tp_:jj: is TP:jj:[:ixp:,:iyp:,1])
(print Tr+_:jj: is tp_:jj:)
(make1 vp_:jj: is 0)
(store1 vp_:jj: is VP:jj:[:ixp:,:iyp:,1])
(print Vd+_:jj: is vp_:jj:)
enddo
save13end
************************************************************
Group 14. Downstream Pressure For PARAB
************************************************************
Group 15. Terminate Sweeps
LSWEEP = 500
RESFAC =1.0E-05
************************************************************
Group 16. Terminate Iterations
LITER(P1)=200
************************************************************
Group 17. Relaxation
RELAX(P1 ,LINRLX,1. )
RELAX(KE ,LINRLX,0.5 )
RELAX(EP ,LINRLX,0.5 )
RELAX(C6 ,LINRLX,0.5 )
RELAX(C7 ,LINRLX,0.5 )
RELAX(C8 ,LINRLX,0.5 )
RELAX(C9 ,LINRLX,0.5 )
RELAX(C10 ,LINRLX,0.5 )
KELIN = 3
************************************************************
Group 18. Limits
VARMAX(C6)=1. ;VARMIN(C6)=0.
VARMAX(C7)=1. ;VARMIN(C7)=0.
VARMAX(C8)=1. ;VARMIN(C8)=0.
VARMAX(C9)=1. ;VARMIN(C9)=0.
VARMAX(C10)=1. ;VARMIN(C10)=0.
************************************************************
Group 19. EARTH Calls To GROUND Station
NAMGRD =FLAR
GENK = T
PARSOL = F
ISG62 = 0
SPEDAT(SET,DFLUX,DFMODL,L,T)
SPEDAT(SET,OUTPUT,NOFIELD,L,T)
SPEDAT(SET,DFLUX,DEPOMOD,I,3)
SPEDAT(SET,DFLUX,DENP1,R,1400.)
SPEDAT(SET,DFLUX,DIAP1,R,1.0E-06)
SPEDAT(SET,DFLUX,DENP2,R,1200.)
SPEDAT(SET,DFLUX,DIAP2,R,3.1E-06)
SPEDAT(SET,DFLUX,DENP3,R,1200.)
SPEDAT(SET,DFLUX,DIAP3,R,5.2E-06)
SPEDAT(SET,DFLUX,DENP4,R,1000.)
SPEDAT(SET,DFLUX,DIAP4,R,9.8E-06)
SPEDAT(SET,DFLUX,DENP5,R,1000.)
SPEDAT(SET,DFLUX,DIAP5,R,1.6E-05)
SPEDAT(SET,GXMONI,PLOTALL,L,T)
************************************************************
Group 20. Preliminary Printout
DISTIL = T ;NULLPR = F
NDST = 0
DSTTOL =1.0E-02
EX(P1)=3.43 ;EX(U1)=5.122
EX(V1)=4.131E-03 ;EX(W1)=4.132E-03
EX(KE)=0.1288 ;EX(EP)=5.773
EX(C6)=0.9999 ;EX(C7)=0.9996
EX(C8)=0.999 ;EX(C9)=0.9978
EX(C10)=0.9735 ;EX(ENUN)=0.01123
EX(DI5)=4515. ;EX(DI4)=1.07E+04
EX(DI3)=2.002E+04 ;EX(DI2)=2.009E+04
EX(VP5)=1.016E-03 ;EX(TP5)=0.4688
EX(VP4)=3.837E-04 ;EX(TP4)=0.177
EX(VP3)=1.317E-04 ;EX(TP3)=0.06069
EX(VP2)=4.805E-05 ;EX(TP2)=0.02202
EX(VS5)=7.688E-03 ;EX(TR5)=7.837E-04
EX(VD5)=2.569E-04 ;EX(DEP5)=3.063E-04
EX(VS4)=2.903E-03 ;EX(TR4)=2.959E-04
EX(VD4)=9.7E-05 ;EX(DEP4)=1.157E-04
EX(VS3)=9.955E-04 ;EX(TR3)=1.015E-04
EX(VP1)=6.963E-06 ;EX(TP1)=2.959E-03
EX(DI1)=1.201E+04 ;EX(VS1)=4.816E-05
EX(TR1)=4.909E-06 ;EX(VD1)=1.806E-06
EX(VD3)=3.33E-05 ;EX(VSTR)=0.03374
EX(DEP1)=2.155E-06 ;EX(DEP3)=3.972E-05
EX(VS2)=3.584E-04 ;EX(ENUL)=1.563E-05
EX(TR2)=3.653E-05 ;EX(VD2)=1.217E-05
EX(DEP2)=1.438E-05 ;EX(YPLS)=3.917
EX(STRS)=9.183E-03 ;EX(EPKE)=28.889999
EX(DEN1)=1.181 ;EX(EL1)=4.675E-03
EX(ENUT)=7.338E-04
EX(C9 )=9.675E-01
EX(C10 )=9.097E-01
EX(DI5 )=6.786E+01
EX(DI4 )=1.212E+03
EX(DI3 )=5.772E+03
EX(DI2 )=3.673E+09
EX(VP5 )=6.433E-03
EX(VP4 )=1.509E-03
EX(VP3 )=2.169E-04
EX(VP2 )=5.702E-05
EX(VD5 )=1.725E-03
EX(DEP5)=1.011E-03
EX(VD4 )=4.076E-04
EX(DEP4)=3.803E-04
EX(VP1 )=7.165E-06
EX(DI1 )=4.563E+10
EX(VD1 )=1.849E-06
EX(VD3 )=5.692E-05
EX(DEP1)=2.206E-06
EX(DEP3)=6.647E-05
EX(VD2 )=1.477E-05
EX(DEP2)=1.758E-05
************************************************************
Group 21. Print-out of Variables
OUTPUT(YPLS,Y,N,Y,N,Y,Y)
OUTPUT(STRS,Y,N,Y,N,Y,Y)
************************************************************
Group 22. Monitor Print-Out
IXMON = 42 ;IYMON = 15 ;IZMON = 1
NPRMON = 100000
NPRMNT = 1
TSTSWP = -1
************************************************************
Group 23.Field Print-Out & Plot Control
NPRINT = 100000
XZPR = T
ISWPRF = 1 ;ISWPRL = 100000
No PATCHes used for this Group
************************************************************
Group 24. Dumps For Restarts
GVIEW(P,0.462061,-0.680528,0.568666)
GVIEW(UP,-0.141691,0.576336,0.804836)
GVIEW(WINDOW,1022,726)
GVIEW(DEPTH,3.0E+04)
GVIEW(VDIS,1.506729)
GVIEW(CENTRE,1.52,0.076,0.076)
> DOM, SIZE, 3.040000E+00, 1.520000E-01, 1.520000E-01
> DOM, MONIT, 2.102666E+00, 7.251333E-02, 1.761008E-03
> DOM, SCALE, 1.000000E+00, 1.000000E+00, 1.000000E+00
> DOM, INCREMENT, 1.000000E-02, 1.000000E-02, 1.000000E-02
> GRID, RSET_X_1, 60, 1.000000E+00
> GRID, RSET_Y_1, -30, 1.050000E+00,G
> GRID, RSET_Z_1, -30, 1.050000E+00,G
> DOM, T_AMBIENT, 2.300000E+01
> DOM, INI_AMB, YES
> DOM, INI_BUOY, YES
> OBJ, NAME, INL
> OBJ, POSITION, 0.000000E+00, 0.000000E+00, 0.000000E+00
> OBJ, SIZE, 0.000000E+00, TO_END, TO_END
> OBJ, DOMCLIP, NO
> OBJ, GEOMETRY, cube3t
> OBJ, VISIBLE, NO
> OBJ, TYPE, INLET
> OBJ, PRESSURE, P_AMBIENT
> OBJ, VELOCITY, 5.3 ,0. ,0.
> OBJ, INLET_C6, 1.
> OBJ, INLET_C7, 1.
> OBJ, INLET_C8, 1.
> OBJ, INLET_C9, 1.
> OBJ, INLET_C10, 1.
> OBJ, TURB-INTENS, 6.8
> OBJ, NAME, OUTL
> OBJ, POSITION, AT_END, 0.000000E+00, 0.000000E+00
> OBJ, SIZE, 0.000000E+00, TO_END, TO_END
> OBJ, DOMCLIP, NO
> OBJ, GEOMETRY, cube12t
> OBJ, VISIBLE, NO
> OBJ, TYPE, OPENING
> OBJ, PRESSURE, P_AMBIENT
> OBJ, COEFFICIENT, 1000.
> OBJ, TURBULENCE, SAME , SAME
> OBJ, NAME, HWAL
> OBJ, POSITION, 0.000000E+00, 0.000000E+00, AT_END
> OBJ, SIZE, TO_END, TO_END, 0.000000E+00
> OBJ, DOMCLIP, NO
> OBJ, GEOMETRY, cube11
> OBJ, VISIBLE, NO
> OBJ, TYPE, PLATE
> OBJ, NAME, SWAL
> OBJ, POSITION, 0.000000E+00, 0.000000E+00, 0.000000E+00
> OBJ, SIZE, TO_END, 0.000000E+00, TO_END
> OBJ, DOMCLIP, NO
> OBJ, GEOMETRY, cube11
> OBJ, VISIBLE, NO
> OBJ, TYPE, PLATE
> OBJ, NAME, NWAL
> OBJ, POSITION, 0.000000E+00, AT_END, 0.000000E+00
> OBJ, SIZE, TO_END, 0.000000E+00, TO_END
> OBJ, DOMCLIP, NO
> OBJ, GEOMETRY, cube11
> OBJ, VISIBLE, NO
> OBJ, TYPE, PLATE
> OBJ, NAME, LWAL
> OBJ, POSITION, 0.000000E+00, 0.000000E+00, 0.000000E+00
> OBJ, SIZE, TO_END, TO_END, 0.000000E+00
> OBJ, DOMCLIP, NO
> OBJ, GEOMETRY, cube11
> OBJ, VISIBLE, NO
> OBJ, TYPE, PLATE
STOP